Home › Blog › Current Post

Your Regrind Margin Doesn’t Survive a Second Melt

2026-11-16 · ZK Hydraulic editorial team

A plastics recycler in Katowice ran granulators for eleven years. Mixed PP and HDPE industrial scrap, sold as regrind across Upper Silesia. The margin, by their own account, no longer covered the processing cost. So last month they pressed their own flake into pallets instead. One tonne of regrind became roughly 75–80 finished pallets. A commodity price became a manufactured product price.

Trade reports from other line builders tell the same story this autumn. A Russian customer accepted a plastic pallet line tested on waste film and worn-out pallet scrap. A Polish granulator moved one step downstream into pressing. Both projects shared one design decision, and that decision is what this article is about: they skipped pelletizing entirely.

What single-melt compression molding actually means

Single-melt compression molding is the practice of pressing a pallet directly from shredded plastic flake, so the polymer is heated exactly once between the bale and the finished pallet. A twin-screw extruder plasticises the flake. The molten charge feeds straight into a hydraulic mold, typically on a 1,500–2,000-ton press. There is no pelletizing step in between. No strands, no water bath, no dicer, no silo, and no second purchase order for pellets you just made yourself.

The opposite route is the familiar one. A granulator melts, strands, cools and cuts the material into pellets. Then a pallet machine melts those pellets again. Every heat history degrades the polymer chain. Two heat histories degrade it twice. For a pallet that has to carry 1.2 tons dynamically and up to 6 tons statically, molecular weight is not an academic detail. It is the load rating.

The money you lose on the second melt

The second melt bills you three times.

First, energy. Line builders in this segment report that skipping the granulation stage cuts total electricity consumption by 30–45%. A granulation line carries its own extruder, cooling water and cutting system. All of that power produces a pellet whose only job is to be melted again.

Second, capital. A pelletizing line is a whole investment block between the crusher and the press. For a recycling plant converting its own scrap, that block adds floor space, maintenance and operators without adding a single saleable unit.

Third, the polymer itself. Virgin resin tolerates repeated melting within spec. Mixed recovered PP and PE does not. The Polish trial ran four batches of real plant scrap through a 1,600-ton press at 1200 × 1000 × 150 mm. Pallets weighed 20–27 kg and passed the customer’s own load test with no virgin resin added. That result depends on keeping the melt count at one.

The unit economics, in plain numbers

Run the arithmetic on a single tonne and the case closes itself.

A tonne of mixed PP/PE flake pressed at typical yields becomes 75–80 pallets. Public Chinese equipment listings put a mid-range press line around USD 90,000–160,000, with a 55 kW main motor and a 20-pallet-per-hour rating on a 1200 mm class mold. Amortize the machine across that output and the per-pallet capital cost lands in cents. Compare that with the resale price of one tonne of regrind. The pellet market moves with virgin resin, and virgin resin has spent this year under tariff pressure.

The waste side can even pay you twice. A site that collects industrial mixed polyolefin waste currently pays disposal gate fees to move it. Once that stream feeds your own press, the gate fee disappears from your cost sheet and a pallet invoice replaces it. Feedstock that used to be a liability becomes the cheapest input in the plant.

Scale matters, though. The line described above turns out 120–160 pallets per shift at 20–27 kg each. That is 3–4 tonnes of flake per shift, and 6–8 tonnes across two shifts, every working day, week after week. That is why feedstock contracts, not press tonnage, decide whether these projects survive year three. Order the press only after the waste stream is secured in writing.

What the press has to forgive

Dirty flake is not a defect here. It is the business model.

A compression line built for recycled feed handles things an injection molding machine cannot. Paper label fragments pass through. Moisture and volatiles escape through degassing zones on the extruder barrel instead of becoming steam pockets inside the mold. Mixed polyolefin ratios that drift week to week simply get re-tested and re-dosed. One line builder now runs waste film and rigid pallet scrap on the same line, with each stream pretreated separately, dewatered mechanically, then blended at a set ratio before the extruder.

Metering is the quiet hero in all of this. On a recycled line, pallet weight variation across consecutive shots tells you whether the dosing system actually works. A stable 20–27 kg window on a 150–180 second cycle is what a buyer should ask to see at acceptance, not a brochure.

If you want the full line architecture — shredding, extrusion, dosing, pressing, demolding — our plastic pallet machine page breaks down each stage. For plants that also handle wood waste or agricultural fiber, the same platform logic extends to a presswood pallet machine line, giving one site two waste streams and two revenue lines.

The feedstock window just opened wider

Two regulatory events this month push more plastic toward exactly this route.

The EU’s plastic waste export ban takes effect on 21 November. Roughly 500,000–800,000 tonnes a year lose their cheapest exit to non-OECD buyers. That material will not become pellet-grade recyclate. It is mixed, contaminated, and priced to move. A pallet press is one of the few machines that turns that grade into a product with its own demand.

Tariffs are doing similar work on the demand side. The UK’s safeguard review left rPET exposed to a 65% duty above quota, which makes imported virgin-grade material dearer and locally recovered flake more attractive by comparison. Meanwhile demand keeps compounding. Future Market Insights puts the global plastic pallets market at USD 8.8 billion in 2025, growing at a 5.8% CAGR toward USD 15.4 billion by 2035.

Traceability rules are converging on the same point. China’s national standard GB/T 47982-2026, in force since 1 November, requires recycled plastic producers to document source, process and batch. A pallet line that presses from your own documented waste stream already satisfies most of that chain of custody. You are not buying someone else’s recyclate claim. You are making it.

When this route makes sense, and when it does not

This route makes sense if you already granulate and the margin is thin. It makes sense if you sit on mixed PP/PE waste with no clean outlet. It makes sense if your buyers ask for verified recycled content, because pressing your own flake makes the claim physically provable.

It does not make sense if your waste is a single clean polymer with a strong pellet market. Sell it. It does not make sense if you cannot secure feedstock volumes. The line described above burns 3–4 tonnes of flake per shift. Spot-buying that volume, week after week, is how pallet margins die in a different way.

Press your own material before you sign anything

No supplier can quote a line configuration for a feedstock they have never pressed. The sequence that works is simple. Send 50–100 kg of your actual scrap. Run it through the extruder and the mold. Adjust temperature, dwell and dosing until the pallet passes your own load test. Then sign.

Recent press-floor trials and regulatory notes live on our news page. If you have flake sitting in a yard and a margin that keeps shrinking, the contact page is the fastest route to a trial slot. And for a wider view of which polymers suit pallet production and why, the palletsbiz overview of recyclable plastics pairs well with this article. The ZK Hydraulic pallet machine resource site collects the same material for buyers comparing press tiers side by side.

Contact Us

Please submit your question. Our team will contact you within 24 hours.