Home › Blog › Current Post

The Line Item Missing From Every Molded Pallet Feasibility Model

A molded plastic pallet press costs 13 to 16 cents a pallet to keep running. That covers hydraulic oil, filters, seals, screw and barrel wear, and the twenty minutes a shift somebody spends clearing vents. Most feasibility models stop at power, labour and flake. The maintenance row is either blank, or it carries one round number that nobody can defend.

That row decides year three. Here is the arithmetic behind it, and here is where the money actually leaves the building.

Why dirty flake is harder on a press than virgin resin

Compression molding exists because it tolerates bad input. That tolerance gets paid for in wear.

Mixed flake arrives with sand, paper fibre, glass fibre, mineral filler and cured resin dust. None of it melts. All of it slides against steel at 200°C under 1,600 tons of clamp. The abrasion is not a slow, even polish either. It concentrates at the feed section and the last few flights of the screw, where pressure peaks.

Metallurgy matters more than the price list suggests. A nitrided barrel carries a hardened case of 0.5 to 0.7 mm. A bimetallic barrel carries 2.0 to 3.0 mm of fused alloy. In abrasive service the bimetallic version runs two to five times longer. The price gap is nowhere near that ratio.

Figures published on the compounding side put wear-part life at 8,000 to 20,000 hours on clean polyolefin. Add glass fibre and the same parts fall to 3,000 to 6,000 hours. A pallet line on two shifts runs about 4,800 hours a year. Do the division and a nitrided screw on glass-filled flake is done inside 8 to 15 months.

The failure is quiet. No bang, no alarm. You get output fluctuation above 5% and specific energy up 8%. Scrap creeps from 2% to 6% across a quarter while everyone blames the flake. Then somebody measures radial clearance and finds 0.5 mm. By that point the nitrided case is gone. Re-machining the bore just wastes a week.

What maintenance cost per pallet actually means

Definition first, because this number gets quoted loosely. Maintenance cost per pallet is annual spend on consumables and wear parts, plus the labour to fit them. Divide it by saleable pallets. It excludes capital, building and power. It includes every pallet scrapped while the machine was misbehaving.

Here is the build-up on a single-station line. It presses 23 kg pallets, 300 a day, 300 days a year. That is 90,000 pallets and roughly 4,800 press hours. For reference, our dual-station plastic pallet press doubles that output without a second mould. It doubles the wear with it.

  • Hydraulic oil: a 700 litre reservoir at $4 a litre, changed once a year — $2,800
  • Return filters: three sets — $180
  • Seal and hose kit, amortised — $1,000
  • Vent cleaning: 120 sessions a year at 20 minutes — $1,200
  • One screw and barrel set every 8 to 15 months — $6,000
  • Heater bands, sensors, ejector pins, release agent — $2,000

That lands near $13,000, or about 14 cents a pallet. Add 40 hours of unplanned downtime, which the industry treats as a good year. That is another 500 pallets gone. A screw swap is worse. It eats one to two days, so 300 to 600 pallets never get invoiced at all.

The honest figure is 13 to 16 cents, before lost sales.

The four things that fail, in the order they fail

Vents go first. Recycled flake carries paper fibre and ash, and both plate out in the vent grooves. A blocked vent shows up as flash on the parting line. Or a short shot at the far corner, or a burn mark at a rib root. Cleaning takes twenty minutes. Re-cut a vent to the wrong depth and you need a new insert, because a vent that runs too deep turns flash into a permanent feature of the tool. The palletsbiz mould library covers insert geometry if you are still at drawing stage.

Hydraulic oil goes second, and mostly because of temperature. The working window is 30 to 55°C. Above 60°C viscosity drops, pressure drifts, and clamp force stops being repeatable. An acid value above 0.5 mgKOH/g means the oil is oxidizing and eating seals. Change oil at 5,000 to 10,000 hours and the return filters every 1,500 hours. Skip the filters and the new oil is dirty inside a shift.

Seals are third, at 10,000 to 20,000 hours. The early symptom is a film of oil around a fitting rather than a drip. Most plants call that acceptable. It is not. A slow internal leak is lost clamp force, and lost clamp force is flash.

Screw and barrel are last, which is the problem. Most expensive item, least visible. Nobody notices until the weight spread across twenty consecutive shots opens up. Then nesting depth stops holding true.

What belongs in the purchase order

Four lines, all cheap at order stage.

Ask for a bimetallic plasticising barrel if your flake carries more than 20% mineral filler or any glass. The premium is smaller than one screw replacement. That replacement is exactly what the premium buys you out of. Put a magnet at the hopper inlet too. Copper strand from cable skin does more damage in a week than sand does in a month. So does tramp steel from shredded appliances.

Size the oil cooler for site ambient, not for the factory in Jiangsu. A line in the Gulf runs at 45°C ambient. It needs more cooling surface than the same press standing in Europe. We size coolers per destination for exactly that reason, and the Arabic-language machine pages carry the Gulf specification in full.

Specify replaceable vent inserts. A vent repair then becomes a swap, not a mould rework. A rework costs press downtime, machining and a fresh approval round.

Spares that should arrive with the press

Sea freight from China runs five to seven weeks. Air freight on a screw is possible and painfully expensive. Plants lose a fortnight in the gap between those two facts.

Order two years of filters and two sets of heater bands with the machine. Add a full seal kit, a dozen ejector pins and two vent inserts. The bundle costs a few thousand dollars. It buys the ability to clear the four most common stoppages without waiting on a container.

One number worth keeping in view. Range International told the ASX in late October about a 35,000-pallet order. It needs a new mould and welding table at roughly $100,000. Their capex line was precise and public. Their maintenance line did not exist. That is how the whole sector plans.

What it does to the payback

Put 15 cents a pallet and 3% downtime into the model. On 90,000 pallets that is $13,500 of maintenance plus about 2,700 pallets of lost output. A payback that read 18 months becomes 20 to 22.

Now run the other version, with a nitrided barrel and two screw events a year. Payback reads 26 months, and the plant spends every second year explaining a variance to its bank.

The difference between those two plants is not the press. It is four lines in a purchase order and one column in a spreadsheet.

Why this matters more this quarter than last

European recyclers rolled November prices over instead of pushing through the increases they had planned. Regenport’s week-two assessment ties that to the 21 November export ban, which traders expect to leave more feedstock inside Europe. The same report notes the rHDPE discount to virgin resin widened. PPWR has had limited effect on recycled uptake so far. Plasteurope logged discounts across standard recyclate grades in October, on weak demand and recyclers cutting production earlier than usual.

Read those together and the conclusion is uncomfortable. Cheap feedstock is not arriving to rescue a thin margin, and higher pallet prices are not arriving either. Once the machine is bolted down, maintenance is the only cost line still under your control.

So the trial matters more than the brochure. Send 50 to 100 kg of your actual flake. We will press it and weigh twenty consecutive shots. Then we tell you what the wear rate looks like on your material, not on a clean pellet. The plastic pallet machine range runs from 800 to 3,000 tons for that reason. Trial results go up on our news page, including the numbers that did not flatter us.

Put the maintenance row in the model before you sign. Our engineers will help you build it. We would rather do that now than explain a screw failure at month fourteen. Send your material and your power tariff, and we will come back with a wear schedule sized to your flake, not to a demo.

Good compression tooling practice is documented elsewhere. The mould industry guidance on compression tool life is worth reading before you approve a drawing. None of it is pallet-specific. All of it applies.

Contact Us

Please submit your question. Our team will contact you within 24 hours.