Home › Blog › Current Post

Your Pallet Left the Press at 9% Moisture. It Landed at 14%.

The claim arrived before the container did: twelve crushed cartons in the bottom third of the load, all of them sitting on pallets from the same batch. The buyer sent photographs, then a number from a pin meter pushed into a deck — 13.9%. The supplier’s goods-out sheet said 8.6%. Both readings were taken honestly. Only one of them was taken correctly, and neither of them described what happened during thirty-five days at sea.

Moisture is the least photographed specification in the presswood business. Nobody puts it on a product page next to tonnage and cycle time, because it does not sell a press. It decides, quietly, whether the pallet that left your yard at 9% is still the pallet you sold when it reaches Rotterdam.

What finished moisture actually is

Finished moisture content is the mass of water remaining in the pressed pallet, expressed as a percentage of the pallet’s total weight, measured after the board has cooled and equalised. It is not the moisture of the furnish going into the mould, and it is not the number a pin meter shows when you stab a hot deck thirty seconds after ejection.

That definition matters because four things follow from it. Density moves with it — the same mould, the same 1,600-tonne press, the same 12 kg of fibre will produce a heavier and softer pallet at 13% than at 8%, because water occupies volume that fibre should be filling. Strength moves with it, since a wet mat consolidates less under the same force. Flatness moves with it, because the board keeps shrinking for days after it leaves the mould. And freight weight moves with it, though by less than most people assume.

Get the number right and the rest of the specification holds. Get it wrong and every figure on the quotation becomes a guess.

Why 9% is a specification and not a habit

Two binder systems dominate this industry, and they want different things from water. Future Market Insights puts urea-formaldehyde and melamine-reinforced resin at 68.7% of the 2026 market, and those systems cure on heat, not on water. Push a 13% mat into a 200°C mould on a four-minute cycle and the water flashes to steam faster than the mat can vent it. The result shows up at the edge: a lifted rim, a hairline separation between deck skin and core, a pallet that passes a visual check at the stack and fails at the first rack impact.

MDI is the opposite animal. It reacts with moisture, which is why MDI lines tolerate wetter furnish and cure in three to five minutes at lower temperature. That tolerance is real and it is also a trap. “MDI doesn’t care about water” is a sentence spoken by people who have never opened a mould after a blowout. MDI needs some water to build strength, and it needs that water evenly distributed — a mat that is dry on the surface and wet in the middle cures into a board with a hard skin and a soft core, and the core is where the pallet fails.

Nine percent, give or take half a point, is where both systems converge: enough water for consolidation and binder reaction, little enough that the steam generated in a hot mould can escape through the parting line in the seconds available.

The arithmetic nobody runs before buying the dryer

Take one 1,200 × 800 mm nine-leg pallet at 13.5 kg finished weight and 9% moisture. The dry fibre in it weighs about 12.3 kg. If the sawdust arriving at your gate sits at 50% moisture — normal for a furniture plant’s baghouse collection in a humid month — you need roughly 24.6 kg of wet furnish to deliver those 12.3 kg of fibre. The other 12.3 kg is water, and every gram has to leave the building through a dryer stack.

That is one pallet. A single-station line on a five-minute cycle makes about 88 pallets a shift, which means the dryer has to evaporate close to a tonne of water before lunch.

Dryers are usually bought on throughput — “two tonnes an hour” — when they should be bought on evaporation. Breaking a kilogram of water out of wood fibre takes roughly 2.26 MJ, before you count the heat that goes up the stack and the heat that stays in the board. A well-run rotary drum lands between 3.2 and 4.2 MJ per kilogram of water, which yields a rule of thumb worth carrying into a supplier meeting: the dryer needs about 6 to 7 kW of thermal output for every pallet per hour the press line produces. A dual-station line making 24 pallets an hour needs roughly 150 to 170 kW of burner, not the 60 kW unit bundled into a cheap quotation.

The fuel choice decides whether that is a cost or a rounding error. Burn your own screened dust and the fuel is free — you pay for fans, a furnace motor, labour and maintenance, on the order of €15-25 per tonne of water removed. Heat electrically and you buy 1,000 to 1,300 kWh for the same tonne: €180-230 at the EU industrial average of €0.18/kWh, over €350 at Germany’s €0.352/kWh. Same dryer, same output, six times the drying cost — which is why two plants with identical floor plans run wildly different cost per pallet.

Your meter is probably reading low, and you know why

The 8.6% on the goods-out sheet and the 13.9% in Rotterdam are not a fraud story. They are a measurement story, and the error has three predictable sources.

The first is temperature. Resistance meters are calibrated around 20°C. A board that has just come off a 200°C mould is still 60-80°C at the core, and the meter reads it as drier than it is — commonly one to three points low. Measure at the press and you will always be optimistic.

The second is the surface. A hot-pressed skin dries faster than the core, so pins driven 8 mm into the face sample the driest part of the pallet, while the core is where the water sits and where the blowout starts. The third is the instrument: pin meters carry a stated accuracy of roughly ±2 points, and the cheaper ones drift with battery voltage and probe wear. Two points is the entire tolerance band of the product.

The fix is unglamorous and nearly free. Pull one pallet per shift, let it cool thirty minutes in the same room as the scale, cut a 20-30 g slug from the centre of a leg, weigh it, dry it at 103 ± 2°C to constant mass, weigh it again. That is the reference number. Check it against what the pin meter said on the same pallet; after a week you will know your meter’s offset, and after a month you will know whether the dryer is drifting or the operator is sampling the easy pallets.

What one point of moisture costs

Cycle time comes first. A wet mat absorbs heat before the binder sees it, and the press sits closed for another 30 to 40 seconds waiting for the core to reach cure temperature. On a 300-second cycle that is a 13% loss of output — eleven pallets a shift on a single-station line, twenty-two on a dual-station one. Nobody writes that loss on an invoice, which is why it survives for years.

Rejects come second. Edge blows and delamination cluster in the 12-14% band, because that is where vapour generation outruns venting. A 3-4% reject rate at 13% moisture is normal; at 9% it should be under 1%.

Flatness comes third, and it is the one that bites export accounts. The footprint of a moulded deck barely moves, because the tool sets it. Thickness and flatness do move. A deck that leaves the mould flat and loses two points over three weeks will cup, and a cupped deck is what a fork misses and a photo-eye misreads. Sell into a cell that specifies ±2 mm on deck height and the moisture specification and the tolerance specification become the same document.

Mould comes last and is the one that ends relationships: fungal growth on wood fibre needs sustained moisture above roughly 20% plus warmth, and a pallet at 9% in a container at 30°C and 85% relative humidity drifts toward equilibrium near 18-19%. Starting at 9% buys headroom. Starting at 13% spends it before the ship sails.

The number buyers will ask for next

A verification service called PalletGrade opened a tool this month that lets a buyer type in — or photograph — an ISPM 15 operator code and get the issuing authority’s record back, covering more than 8,500 registered operators across 14 countries. The era of taking a stamp on trust is closing. Which raises an obvious question for anyone selling ISPM 15 exempt moulded pallets: if the stamp is now checkable, what about the number the stamp was standing in for?

For presswood the exemption is a material argument, not a stamp argument. Processed wood fibre pressed with a binder at 150-200°C sits outside the scope of the wood packaging standard, and no mark is required or issued. That is a real commercial advantage, and it is also why moisture records matter more here than in a sawmill: with no third-party mark to point at, the technical file is the evidence — furnish source, press curve, core temperature log, finished moisture per batch.

Several suppliers now advertise the internal temperature of the mat — “above 105°C internally, held over 56°C for thirty minutes” — as a phytosanitary credential. It may be true of their cycle. It is only an argument if the thermocouple data exists and is archived per batch; otherwise it is a sentence on a website, and buyers who have learned to check operator codes will learn to ask for the log.

What to put in the enquiry

Ask what moisture the dryer is specified to deliver at the outlet, not what the press can tolerate. Ask for evaporation in kg of water per hour and burner output in kW, then divide by your own pallet weight and see whether the numbers survive. Ask whether the check is pin or oven-dry, where the sample is taken, and how long the pallet cools before weighing.

Then ask the question that separates a line supplier from an equipment seller: what happens to cycle time when my furnish arrives at 55% instead of 45%? Anyone who answers “no change” has not run a line through a rainy season.

The press is the part of the investment that gets photographed. The dryer is the part that decides your yield, and moisture is the number that tells you whether you own the process or are just running it. The presswood pallet machine specification and the capacity calculation show how the two are sized against each other on a real layout — and if you would rather test it on your own sawdust, send us a sample and we will dry it, press it, and send back the moisture curve with the load figures.

Request a Quote

Please submit your question. Our team will contact you within 24 hours.