A molded recycled plastic pallet is a one-piece platform pressed from unwashed mixed polyolefin flake. That includes the LDPE film grades most recycling plants refuse. From 21 November 2026, Regulation (EU) 2024/1157 closes the cheapest exit for Europe’s worst bales. Roughly 500,000 to 800,000 tonnes a year lose the route to non-OECD buyers. Low-grade film carries most of that weight. Washing lines will not take it at a profit. Landfill and incineration taxes will eat the margin. One machine still converts that flake into a product with stable demand — a hydraulic press of 800 to 3,000 tons.
What actually closes on 21 November
The ban is narrow on paper and wide in effect. It stops EU exports of plastic waste to countries outside the OECD. It does not stop trade inside the OECD. It does not stop pellets. It does not stop end-of-waste flake either; member states adopted those harmonised criteria on 3 November.
The volume is the problem. Our earlier analysis of the export ban estimated that 500,000 to 800,000 tonnes a year were flowing to non-OECD destinations. That material now stays in Europe, or it competes for the one open lane — Turkey.
The legal text sits on EUR-Lex, and the Commission’s waste shipment pages track the prior-informed-consent paperwork that has already slowed cross-border moves this year. Bookmark both. Neither decides your bale price, though. The grade mix does. ICIS analysts devoted a 13 November podcast to the ban’s impact on recycled polyethylene. Their 18-month rPE forecast starts from the same premise: lower-quality LDPE bales face the hardest landing. They have the fewest domestic outlets and the weakest quality spec.
Turkey cannot absorb it either
Turkey is an OECD member, so the ban does not touch it. On the surface, that lane stays open. The numbers behind it tell a harder story.
Turkey imported about 510,000 tonnes of EU plastic waste in 2025. That single country took 70% of all EU exports bound for OECD members and 36% of global flows. Reporting from Adana province this week described irrigation canals choked with plastic debris. Local facilities logged around 200 fires a year. The Turkish government cites a 38% recycling rate. Independent assessments put it closer to 12%.
So the lane is open, but the destination is already full. A Commission assessment published in mid-November documented concerns about data transparency and enforcement, yet allowed shipments to continue. WasteTrade’s November review of African recycling markets drew the same conclusion from another direction. Cheap imported waste is no longer a dependable assumption anywhere. Buyers now pay for proven quality, not tonnage.
If you sit on film bales in Europe, the practical picture is this. Your best grades still sell. Your low-grade film does not. Turkey will not clear a price for it. Washing lines would rather buy cleaner feedstock.
Washing is the cost nobody models
Why can’t the washing plants just take it? Energy is the honest answer, and a 2026 Turkish process study finally put numbers on it.
The study modeled four polymer streams against ISO 14040/14044 life-cycle rules. Baseline LDPE recycling demanded 1,142 kWh of electricity and 521 cubic meters of natural gas per tonne. PET was worse at 1,210 kWh per tonne. Even with staged batch separation and heat-exchanger upgrades, LDPE still needed about 891 kWh per tonne. Add wash water treatment, drying, and pelletising, and the chain only makes sense on clean, well-sorted flake.
Film is the opposite of clean. Stretch wrap carries tape, labels, and heavy inks. Agricultural film carries soil and stones. Post-consumer packaging film mixes PE with barrier layers nobody can separate economically. Washing that material drives the energy bill above the resin value. That is why it went overseas in the first place.
The press route: dirty flake in, load-bearing pallet out
Compression moulding was engineered for exactly this stream, and the process chain is short. Shred. Metal-detect. Plasticise once. Dose by weight. Press.
No wash water. No gas dryer. No pelletiser. The flake goes in dirty and comes out as a structural product.
Our own trial data shows what that means in units a plant manager reads. Our ZK-P1800 press ran a four-core-pulling mold on 100% mixed recycled plastic. It formed a 1,300 × 1,100 mm pallet at 23 kg. The cycle took 60 seconds. Loads measured 2,000 kg dynamic and 6,000 kg static against ISO 8611 methods. Total line energy ran 2 to 3.5 kWh per pallet. That is roughly 90 to 150 kWh per tonne at 21–25 kg pieces. Set that beside the washing line’s 1,142 kWh per tonne. The gap is about an order of magnitude.
The plastic pallet machine range covers 800 to 3,000 tons because film streams vary week to week. A mixed PP/HDPE ratio drifts, and the press recipe follows it. At 23 kg a piece, one tonne of flake yields about 43 pallets. Mixed PE bales trade near ¥2,000–3,000 per tonne in Chinese markets — about $280–420. The material inside one pallet costs $6–10. Recycled pallets sell between $9 and $22 depending on size and load rating. The spread survives a weak resin market; a washing line’s spread does not.
One rule from the end-of-waste criteria still applies. If your flake carries more than 1.9% foreign matter, it never stops being waste. Our guide to the 1.9% line explains why that is a procurement problem, not a machine problem. The press accepts what the regulation does not — it just prices the sorting burden into the feedstock contract.
What to ask before you commit
Three checks separate a working film-bale line from an expensive experiment.
First, run your actual bale. Ask any supplier to press 50–100 kg of your real flake before quoting a machine. A lab sample of clean regrind proves nothing about your yard stock.
Second, weigh twenty consecutive shots. A spread inside 0.3 kg means the dosing holds and the nesting depth stays true. The pallet weight you advertise is then the weight you ship. The trade-wall analysis from 12 November lists the same test for flake buyers facing tariff walls.
Third, ask how the line handles drift. Film composition changes with the season — more agricultural wrap after harvest, more packaging film before holidays. The press recipe, the venting schedule, and the mold temperature all need headroom for it.
The palletsbiz guide to recyclable plastics and pallets maps which streams press well and which ones need blending. It is the shortest path to a realistic yield estimate before you sign anything.
The door closes on Friday. The bales do not.
Whatever your position in the chain, the date does not move. Collectors will stockpile and hope. Traders will chase the Turkish lane until its fullness becomes a price. Washers will keep buying clean flake and ignoring yours.
The option list is short, and every entry has a price. Stockpiling costs rent and ties up working capital. The Turkish lane pays collection-grade prices and adds a freight bill on top. Incineration and landfill taxes rise almost every year across EU member states. Pressing nearby keeps the chain short. The flake travels once, the pallet travels many times, and the margin stays with whoever holds the mold.
The plants that win on Friday already hold a press within a few hundred kilometers of the bale yard. A tonne of stranded film becomes 43 pallets a warehouse will buy next month. The alternative is a disposal bill that arrives next week.
If you want to test that claim on your own material, send us 100 kg of your worst bale. We will press it before you commit to steel. Every claim on our news page carries the same kind of trial data. Send the feedstock details through the contact page. We will return the results with weights, cycle times, and load figures.